How to fix Vizio TV remote sensor not working

• It's very frustrating when your VizioTV remote is not working, because the TV is almost useless.
• So it's very important to have a functional remote and also to take care of it, for a longer life span. Unless some parts get broken, of course.
• This article is part of a larger section dedicated to fixing hardware problems, so check it out.
• And in our Streaming Hub, you will surely find more useful articles.

The Vizio remote is important for the use of your Vizio smart TV, since you use it to navigate through the menu and various applications.

If the Vizio remote stops working, it can be due to low batteries, a blocked TV sensor, power residue of remote and TV, dirty power source, stuck memory of the remote, or issues with the TV itself.

In this article, we will offer a few tips on how to fix the remote, provided that the functionality is not affected by a flawed IR sensor.

---

How do I fix my VizioTV remote?

1. Change batteries

This is the quickest solution to make sure the remote is working is changing the batteries with fresh ones. Most Vizio remotes will take either two AA batters or two AAA batteries.

If the new batteries don’t solve, the problem, move on to the next solution. 

---

Thinking of buying rechargeable batteries? Check out these recommendations for excellent chargers.

---

2. Power Cycle The Remote

Take the batteries out of the remote. Press the power button and hold for a few seconds then release.

Then, press every single button on the remote while the batteries are out. Press each button at least once. This helps to clear residual power from the remote.

Put the batteries back in and test the remote again to see if it works.

---

3. Power Cycle the TV

1. Unplug the TV from the power outlet.
2. Press and hold down the TV’s power button for a few seconds, wait for one minute.
3. Plug the TV back into the power source and power it on.

Alternatively, change the TV powers source, if possible.

---

4. Clear the way to the TV sensor

The IR sensor of the TV is usually located either on the bottom left or bottom right of the TV. The sensor is very sensitive to anything that might block it, even protective plastic wrap that comes with new TVs.

So move anything that might be in front of the sensor, including books, picture frames etc.

Also, use a cotton swab with a bit of distilled alcohol to clean any impurities on the Tv sensor and also on the IR remote sensor ( the small lightbulb on the remote‘s front edge).

---

5. Reset Remote to Clear the Memory (for Universal Remotes)

1. Press and hold the Set or Setup button. Release the button LED on the top of the remote light blinks twice.
2. Type in the reset code of your remote, most Vizio universal remotes have a reset code of 981 or 977. You can also consult your remote’s manual to find the reset code.
3. Again, the LED should flash twice. This means that the memory has been cleared and any firmware issues should be resolved.
4.  Switch it back to TV using the button at the bottom of the remote and see if it works.

---

If the problem persists, the problem might be related to the IR sensor. The only solution here is to replace it altogether or to change the sensor.

For the first solution, check Vizio’s offer for remote controls, as they sell various models for all TVs. Also, contact Vizio technical support at 1 (888) 849-4623 for more information.

---

FAQ: Read more about VizioTV remote issues

• Why is my Vizio TV remote not working?

There might be many causes, the most common being low batteries, a blocked TV sensor, or residue stuck inside the remote buttons. Each of these is easy to solve.

• How do I fix my TV remote sensor?

Unless there’s a problem with the sensor itself, in which case it needs to be replaced, just make sure that nothing is blocking the communication between the remote and the TV sensor. Also, you can clean both sensors with a cotton swab dipped in alcohol.

• How do I reset my Vizio remote control?

To resent your Vizio remote control, take out the batteries, push the power button for a few seconds, then push firmly each button. Then put the batteries back in.

and

If you are looking for a cheap and genuine microsoft product key, 1-for-1 warranty from us for 1 year.
It will be available at the link: https://officerambo.com/shop/

Very pleased to serve you
Thank you :))